AIS installation: who can carry out the work
RS and RKO rules: practical application
When ordering NSR NSI-1000 agree on the installer as well as the equipment package. Supplying the transponder, installing it, and handing over the completed work are distinct responsibilities. For a ship covered by these RS Rules, the AIS installer must meet a specific requirement.

What Appendix 6 requires
Clause 1.1 of Appendix 6 to Part V, Navigational Equipment, of the RS Rules for the Equipment of Sea-Going Ships identifies two categories of installer: specialists from the equipment manufacturer and enterprises recognized by the Register for this work. It expressly prohibits installation by the ship's crew or by unrecognized organizations.
This guide uses the edition dated 1 January 2026. Clause 1.1.1 of Part V covers self-propelled ships not engaged in international voyages and the navigational equipment intended for them. Under clause 1.1.3, additional instructions from the flag State maritime administration take precedence in case of conflict. Confirm the applicable edition and requirements for your vessel before placing the order.
The appendix covers AIS installation work. Routine watchkeeping with an installed unit serves a different purpose. Specify the planned scope, such as equipment supply, installation, survey of components to be retained, or separate service work.
How to verify the two categories of installer
If manufacturer specialists will install the unit, record who will do the work and what establishes that they are acting in that capacity. Seller status or stock availability alone does not show that manufacturer specialists will take part in the installation.
For another enterprise, confirm that the Register recognizes it for the specific work. Request the relevant documents and verify their scope, validity, and connection to the selected contractor. A general reference to RS on the company's website leaves those points open.
The official RS page on recognition of enterprises treats manufacturers, testing laboratories, and service suppliers separately. These roles cover different activities. A document covering manufacture or testing should therefore not be taken as proof that the required installation work is within its scope.
What to specify in the order
| Item to agree on | What the parties need to know |
|---|---|
| Installer | Name of the installer and the basis for carrying out the work under the requirement. |
| The equipment | Exact AIS variant, units, antennas, and accessories in the selected package. |
| Components to retain | Equipment and circuits to retain after survey and confirmation of suitability. |
| Scope of work | What is included in supply, installation, configuration, and testing of the particular station. |
| Handover deliverables | Agreed documents and records of completed work and checks. |
This table helps write a clear scope. It is not a separate mandatory Register form. The supplier and installer may be the same company or different organizations. Assign responsibility for the actual work and confirm that the supporting documents cover it.
To replace an existing AIS, first list the equipment that will be retained. The exact package is discussed in the guide to the NSI-1000 replacement equipment list. A matching connector or similar mounting still requires technical verification. Selecting the installer does not replace that part of preparation.
How this applies to the NSI-1000
NSR describes the NSI-1000 as a Class A marine AIS with a separate transponder and display and interfaces to navigation equipment. This establishes the model's role in the example. Confirm the package contents and applicable documentation for the offered variant and the specific vessel.
State the vessel, whether this is a first installation or a replacement, the parts to retain, and the proposed work scope. Identify the selected installer or say that one still needs to be agreed. The quotation should distinguish the purchased equipment from arrangements for installation. Model availability does not establish an installer's qualifications.
Sources: RS, Part V, Navigational Equipment, edition dated 1 January 2026, clauses 1.1.1 and 1.1.3, and Appendix 6, clause 1.1. RS: recognition and verification of enterprises; official NSR NSI-1000 page.
More in this series
- Portable GMDSS: gloved operation and readiness for use
- New equipment near the magnetic compass: what to agree
- Echo-sounder trunk: access and water detection
- AIS: accounting for audible fault alarms
- NGR3000 antenna: information needed before choosing a location
- Echo-sounder cable: routing, shielding and deck connections
- EPIRB: float-free release and access to the container
- AIS-SART: the mounting arrangement is part of the package
- NTW-1000: checking the emergency-battery expiry date
- Echo-sounder transducer: conditions around the installation site
- Position source for GMDSS: include power supply in the brief
- AIS pilot plug: what to agree for the bridge
- DSC watchkeeping: the alarm must cover the whole bridge
- NAVTEX: bringing an SAR message to the watchkeeper's attention
- Speed log for a project: speed through the water or over the ground
- EPIRB for a particular vessel: data, markings and documents
- AIS class in the enquiry: start with the vessel's requirement
- Portable GMDSS: storage and transfer to survival craft
- Marine VHF antenna system: what to include in the work specification
- Charging the radio reserve battery: monitoring on the bridge
- Replacing an echo sounder: installation design and onboard documents
- EPIRB Checks: Self-Test and Supporting Document
- Grounding a navigation instrument: what to include in the design
- Navigation switchboard: separate feeders and connected loads