AIS pilot plug: what to agree for the bridge
RS and RKO rules: practical application
When selecting NSR NSI-1000 the external-connections list may describe data sources and outputs to navigation equipment in detail. The intended connection for the pilot's computer needs separate consideration. The connector's purpose, its bridge location and the documented connection to the AIS equipment all matter.

What the RS clause requires
Under clause 3.4.9.4 of Part V, Navigation Equipment, of the RS Rules, a connector must be installed on the navigation bridge near the pilot's workstation, allowing the pilot to connect a personal computer to the AIS equipment.
This article uses the edition of Part V dated 01.01.2026. Under clause 1.1.1, the Part covers self-propelled ships not engaged on international voyages and equipment intended for them. Flag State maritime-administration instructions are considered under clause 1.1.3. Applicability to another vessel must be established separately. This article discusses the intended connection; it does not prescribe the mandatory AIS class or number of installations.
Consider the connector in relation to the workstation
Clause 3.4.9.4 addresses more than a connector being present on one of the units: it specifies a location near the pilot's position on the bridge. For a retrofit, provide a wheelhouse plan showing this workstation and the proposed connection point.
If an existing connector is to be retained, identify where its cable runs and which equipment it serves. An externally intact panel does not establish a connection to the new AIS. If a new connector is required, its configuration and necessary accessories must be included in the agreed scope.
Unit locations and the connection point are distinct
Clause 3.4.9.1 requires convenient use of the AIS display and controls in the wheelhouse. Under clause 3.4.9.2, units that do not require operational control may be placed in an equipment room or a dedicated enclosure near the wheelhouse.
This possibility does not move the pilot's workstation along with the radio unit. The diagram should show both the units and the intended connection point on the bridge. This is particularly useful when replacing equipment whose display, transponder and existing external panel are in different locations.
What the NSI-1000 documentation confirms
Manufacturer NSR describes the NSI-1000 as a shipborne Class A AIS with separate transponder and display units and external interfaces. This confirms the model's AIS role for the task being discussed. Check the exact pilot-connection arrangement and the proposed configuration against its documentation.
The NSI-1000 rev16 brochure lists Pilot Plug NPP100 as an option. If the chosen solution requires NPP100, list it separately in the quotation together with the associated cables and work. An optional accessory is not automatically included in every NSI-1000 supply; its inclusion and configuration must be recorded in the specification.
Clause 3.4.9.4 does not itself provide this article with a pin assignment, connector shape or port settings. These cannot be reconstructed from the number of contacts in a photograph. Likewise, an advertised list of navigation interfaces does not confirm that any computer can be connected using an arbitrary adapter.
For a quotation, provide the models at both ends of the existing connection, panel documentation and the known purpose of the AIS port. If the connection to the previous equipment cannot be traced, a survey is needed. A random adapter cable should not be included merely because it physically joins two connectors.
Information for a quotation
| Background information | What to agree on |
|---|---|
| Vessel and equipment documents | Applicable scope of the requirements |
| Bridge plan and pilot's position | Location of the connection point |
| AIS unit models | Their locations and interface configurations |
| Existing panel and cable | Purpose and suitability for retention |
| Available diagrams and manuals | Documented connection arrangement |
| Required result of the work | Accessory supply, installation and verification |
Agree what must be demonstrated after the intended work. Receiving nearby targets on the display relates to the AIS installation itself and does not confirm the separate connection to the pilot's computer. Verify that connection under the design and manuals, preserving the established arrangements for operating the ship's equipment.
In an enquiry for NSI-1000 distinguish the supplied units, retained panel, necessary accessories and work. The quotation confirms the exact configuration, documents, compatibility of the particular connection, condition, availability, cost and delivery schedule. This article does not propose a procedure for independently wiring connectors or configuring the equipment.
Sources
- RS: Part V of the Rules for the Equipment of Sea-Going Ships, edition 01.01.2026: clauses 1.1.1, 1.1.3, 3.4.9.1, 3.4.9.2 and 3.4.9.4.
- NSR: NSI-1000 AIS CLASS A.
- NSR: NSI-1000 rev16 brochure, optional NPP100.
- NSI-1000: SpectraTech's own product page.
The table and enquiry questions are editorial explanations. Sources consulted: 25 October 2026, Astana.
More in this series
- Portable GMDSS: gloved operation and readiness for use
- New equipment near the magnetic compass: what to agree
- Echo-sounder trunk: access and water detection
- AIS: accounting for audible fault alarms
- NGR3000 antenna: information needed before choosing a location
- Echo-sounder cable: routing, shielding and deck connections
- EPIRB: float-free release and access to the container
- AIS-SART: the mounting arrangement is part of the package
- NTW-1000: checking the emergency-battery expiry date
- Echo-sounder transducer: conditions around the installation site
- Position source for GMDSS: include power supply in the brief