+7 381 249-00-02Please email usRequest a quote
  1. Home
  2. Articles and guides
  3. AIS: accounting for audible fault alarms
Practical technical guide // RS and RKO rules

AIS: accounting for audible fault alarms

When replacing an AIS installation with NSR NSI-1000 it is easy to describe the display, antennas and data sources in detail while leaving another connection unresolved: where the equipment fault signal goes. Targets on the screen concern the operation of the information workstation. Agreeing on the alarm arrangement requires separate information about the shipboard installation.

Request a quote

Conceptual AIS equipment and a separate amber status unit on a bridge; an editorial illustration without a connection diagram.
Conceptual illustration of the alarm arrangement discussed. A separate external device is not required in every configuration; the drawing does not establish the NSI-1000 relay configuration or a complete connection circuit.

The requirement considered here

Clause 3.4.9.3 of Part V, Navigation Equipment, of the RS Rules for the Equipment of Sea-Going Ships addresses the output contacts of a relay activated when AIS equipment faults are detected. These contacts must be connected to a device providing an audible alarm.

This article considers the edition of Part V dated 01.01.2026. Under clause 1.1.1, its requirements cover self-propelled ships not engaged on international voyages and navigation equipment intended for them. Flag State maritime-administration instructions are considered under clause 1.1.3. Applicability to another vessel must be established separately. This article does not determine the mandatory AIS class or number of installations for a vessel.

A separate sounder is not required in every configuration

Clause 3.4.9.3 lists acceptable audible alarm arrangements: a loudspeaker built into the AIS equipment, a separate external audible device, or an alarm system located on the navigation bridge.

The purchasing decision therefore cannot be reduced to a rule that everyone must buy an external buzzer. First establish which arrangement is intended for the installation under consideration and how it is implemented in the particular equipment version. The presence of an ordinary loudspeaker or a similar-looking connector does not, by itself, confirm that the required function is provided.

If the vessel already uses a common bridge alarm system, identify its model in the enquiry and provide the available diagram. If the AIS unit's own audible device is to be used, request confirmation of this arrangement against the documentation for the version offered. Choosing an arrangement does not remove the need to agree on its entire signal path.

The target display does not establish that the alarm circuit works

After replacement, the equipment may receive messages and display nearby vessels. This does not establish that the separate connection to the audible alarm device works. These functions concern different parts of the work scope and must remain distinguishable when agreeing on the outcome.

Likewise, the name of a data interface does not describe the purpose of relay contacts. Do not transfer the wiring arrangement of an old AIS unit to a new one merely because the terminal count or connector appearance is similar. Manuals for the particular units and the contractor's proposed solution are needed. This article specifies no pin assignment, circuit electrical parameters or method of deliberately creating a fault.

Information to send with the enquiry

Background informationWhat it helps establish
Full identification of the existing AIS equipment and its unitsWhich parts of the installation will change
The audible alarm arrangement in useA built-in device, separate instrument or common system
External device model and available diagramThe intended signal recipient and its connections
Documentation and identification of the cable to be retainedWhether it can be used after replacement
Known messages and observations concerning the old workstationThe initial condition for the contractor
Supply and work boundariesWho selects the accessories, carries out installation and confirms the outcome

If the device or the purpose of a cable is unknown, identify this as a survey question. Photographs of labels supplement the documents but do not replace information about contact functions. There is no need to disconnect operational circuits yourself to prepare a commercial enquiry.

How to specify the outcome in the quotation

For NSI-1000 ask for separate details of the hardware, selected alarm arrangement, necessary accessories and associated work. A model being listed in the catalogue does not confirm a particular relay configuration, compatibility with an unidentified shipboard system or compliance of the complete installation.

Agree on the documented outcome the contractor must provide after the specified work. Checking that the delivered units are complete and checking the audible alarm of the assembled installation serve different purposes. Responsible specialists determine the procedure and permitted actions using the applicable documents; this article does not propose arbitrary tests on an operational AIS installation.

In the enquiry, specify the vessel, existing configuration, required quantity, delivery location and preferred date. SpectraTech confirms the exact scope, version, condition, documents, availability, price and lead time in its quotation.

Sources

The table and enquiry questions are practical editorial explanations. Sources reviewed: 25 October 2026, Astana.

More in this series

Request a quote