+7 381 249-00-02Please email usRequest a quote
  1. Home
  2. Articles and guides
  3. NGR3000 antenna: information needed before choosing a location
Practical technical guide // RS and RKO rules

NGR3000 antenna: information needed before choosing a location

For NSR NGR3000 a convenient display position can be chosen in the wheelhouse, but the antenna section requires its own information. The roof already carries radar, transmitting antennas and metal structures; an available mounting point is not necessarily suitable for satellite reception. Before ordering, consider the antenna surroundings and cable route as parts of a single installation.

Request a quote

Conceptual GNSS antenna on a separate tall support above an open ship's roof; an editorial illustration without dimensions.
Conceptual image of unobstructed antenna surroundings. Heights and distances in the drawing are not installation data and do not establish compliance with RS section 4.4.

Where the cited clauses apply

Section 4.4 of Part V, Navigation Equipment, of the RS Rules for the Equipment of Sea-Going Ships concerns antennas for electronic position-fixing system receivers. This article uses the edition dated 01.01.2026; ESOM is the Russian abbreviation for an electronic position-fixing system.

Under clause 1.1.1, this Part covers self-propelled ships not engaged on international voyages and equipment intended for them. Additional Flag State maritime-administration instructions are considered under clause 1.1.3. Applicability to another vessel must be established separately. A satellite navigator being listed in the catalogue does not determine the equipment requirements for every vessel or confirm a selected antenna location.

Open sky and surrounding metal structures

Clause 4.4.1 prohibits installing radio-navigation receiver antennas below large metal ship structures. Under clause 4.4.3, the location of a satellite receiver antenna must allow unobstructed tracking of the satellite constellation; the antenna must be at least 1 m above horizontal surfaces of ship structures.

These are two related conditions, rather than advice to use any tall bracket. Assessment requires views of the surroundings: what is above, nearby and along the horizon, and which horizontal surfaces relate to the proposed location. A close-up photograph of a single antenna does not show this context.

During replacement, an old location cannot automatically be considered suitable merely because the previous navigator once provided coordinates. Structures, equipment or the installation's purpose may have changed. Dimensions and documents allow the contractor to assess the current configuration.

Higher does not mean at the masthead

Clause 4.4.2 separately lists places where these antennas must not be installed: mastheads, areas of strong vibration, spaces beneath deck structures and rigging, and locations near sources of heat or smoke.

A general request to raise the antenna as high as possible is therefore insufficient for a work specification. Identify the proposed support structure, surrounding equipment and known site conditions. The need for a survey and a suitable mounting method are established using the design and documentation. There is no need to climb the mast yourself for an enquiry: provide available drawings and materials obtained safely.

Assess transmitting antennas and radar separately

Under clause 4.4.1, separation from any transmitting antennas must be at least 3 m. Clause 4.4.4 prohibits locating radio-navigation receiver antennas in the direction of the main lobe of the radar antenna radiation pattern.

Meeting one separation distance does not establish compliance with the remaining conditions of the section. For example, distance from a transmitting antenna alone does not describe the position relative to the radar's main lobe. Assessment requires the exact models of nearby equipment, their relative locations and the relevant documents. These figures must not be treated as a single universal installation arrangement for all vessels.

What to attach to the request

InformationWhy it is needed
Vessel type and applicable documentsEstablish which requirements apply
Roof or mast equipment plan and views of the surroundingsAssess the structures and proposed support
Transmitting antenna locations and modelsAssess the relevant nearby equipment
Radar model and antenna installation detailsAssess the main-lobe direction
Identification of any GNSS antenna to be retainedCheck it against the selected navigator
Cable route to the unit and penetration detailsAgree on the cable section and accessories

The table helps collect initial information; it does not replace design assessment. If some dimensions are unknown, clarifying them remains a separate task rather than being replaced with a distance estimate from a photograph.

Relating the installation location to the equipment package

The product page for NGR3000 mentions an antenna and cables. The current quotation must specify their exact identifiers, lengths and accessories for the agreed location. An existing antenna does not become compatible solely because its connector looks similar; a new one should likewise not be ordered without a defined task.

Antenna location, navigator configuration and the conditions for using differential corrections are separate matters. Section 4.4 does not promise the accuracy of a particular installation or DGNSS availability. Version, documents, scope, condition, availability, price and delivery time are confirmed separately.

Sources

The table and enquiry questions are practical editorial explanations. Sources reviewed: 25 October 2026, Astana.

More in this series

Request a quote