Position source for GMDSS: include power supply in the brief
RS and RKO rules: practical application
If the NSR NGR3000 is being considered as the position source for a GMDSS radio installation, the specification needs to cover two related items: data delivery and receiver power. A navigator display running from the ship’s normal supply does not show which source will power the receiver when the radio installation operates on reserve power.

When this requirement applies
Paragraph 2.2.4 of Part V, Navigational Equipment, of the RS Rules applies to radionavigation receivers used to feed the ship’s position and the time at which it was determined automatically into GMDSS radio installations. These receivers must also be supplied by the reserve source of energy for the radio installation required under paragraph 2.2.3 of Part IV, Radio Equipment.
The requirement applies to this specific use of the data source. It does not establish that every installed GNSS receiver is connected to the GMDSS installation or that buying one makes the installation ready. Identify the receiver’s role in the vessel’s system from the design and documentation.
This article refers to the 1 January 2026 version of Part V. Paragraph 1.1.1 covers self-propelled ships not engaged in international voyages and the equipment intended for them. Consider the flag Administration’s instructions under paragraph 1.1.3. Establish applicability separately for other vessels. The article does not calculate battery capacity or required reserve duration, or specify a changeover circuit.
Why consider the NGR3000
NSR describes the NGR-1000 and NGR-3000 as marine GNSS receivers with navigation displays and GNSS data outputs. This makes the NGR3000 a relevant option as a position source. For the intended radio installation, separately confirm the required messages, output configuration, connection and how the receiving equipment accepts the data.
A shared interface label alone is not enough to decide whether to include a receiver in a particular installation. If the source already on board is to remain, give its full designation and the current wiring diagram. For a new source, identify its place in the system before ordering accessories.
Add a power schedule to the data schedule
Start with the receiving radio installation and the position source specified for it. Identify what powers the receiver and what will supply it when the radio installation runs on reserve power. A single diagram can show both, with the data and power lines clearly distinguished.
List any separate data distributors or other intermediate devices by model and function. The installer should consider their role and power supply as part of the actual design. Paragraph 2.2.4 does not provide a ready-made wiring diagram for an arbitrary combination of units.
A wide input-voltage range on one device does not establish that a reserve source is available. A source adequate for one receiver cannot be assumed adequate for the entire radio installation without a calculation. Use the documentation and list the actual loads in addition to the nominal voltage.
What result to agree on after the work
Define the installation states to be checked and the information that the selected source must deliver to the radio installation. Checking whether the receiver powers on and checking the intended data exchange are separate tasks. The documented result should cover the agreed scope, including the associated power supply.
The responsible specialists determine the test programme and permitted actions from the design and manuals. This article does not call for arbitrary disconnection of ship power to demonstrate operation. It does not prescribe allowable data interruption, changeover time or endurance, because paragraph 2.2.4 alone does not establish them.
What to include in an enquiry
| Information | What's the point? |
|---|---|
| Vessel and applicable documents | Scope of requirements and purpose of the installation |
| GMDSS radio installation | Specific equipment receiving position and time |
| Source of position | Model, version, required outputs and data |
| Existing power supply arrangement | Main supply and planned reserve arrangement |
| Intermediate devices | Functions, models and connections to be retained |
| Work required | Supply scope and result to be documented |
For NGR3000 agree on the exact version and accessories for this job. A catalogue listing does not establish that the model is ready to connect to any radio or is compatible with an unidentified power source. Set out the documentation, package contents, condition, availability, cost and lead time in the quotation.
Sources
- RS: Part V of the Rules for the Equipment of Sea-Going Ships, edition 01.01.2026: paragraphs 1.1.1 and 1.1.3, and the full text of paragraph 2.2.4 with its reference to Part IV. This article does not restate the numerical requirements of Part IV.
- NSR: Purpose and outputs of the NGR-1000 and NGR-3000 GNSS receivers.
- NGR3000 — SpectraTech product page.
The table and enquiry questions are editorial explanations. Sources consulted: 25 October 2026, Astana.
More in this series
- Portable GMDSS: gloved operation and readiness for use
- New equipment near the magnetic compass: what to agree
- Echo-sounder trunk: access and water detection
- AIS: accounting for audible fault alarms
- NGR3000 antenna: information needed before choosing a location
- Echo-sounder cable: routing, shielding and deck connections
- EPIRB: float-free release and access to the container
- AIS-SART: the mounting arrangement is part of the package
- NTW-1000: checking the emergency-battery expiry date
- Echo-sounder transducer: conditions around the installation site
- AIS pilot plug: what to agree for the bridge