+7 381 249-00-02Please email usRequest a quote
  1. Home
  2. Articles and guides
  3. Echo-sounder cable: routing, shielding and deck connections
Practical technical guide // RS and RKO rules

Echo-sounder cable: routing, shielding and deck connections

When selecting NSR NED-3010 transducer designation and cable length are only the starting points for specifying the line. For an existing vessel, document the actual route, shielding, connection points and bends before ordering. A straight-line distance between the units does not describe the cable route.

Request a quote

Illustrative enclosed echo sounder cable route and protected connections in a dry equipment room.
Illustrative enclosed route and accessories. The image does not establish bend radius, IP56 protection or cable compatibility with the NED-3010. It is neither a wiring diagram nor a test procedure.

Requirements covered here

Section 3.5 of Part V, Navigational Equipment, of the RS Rules for the Equipment of Sea-Going Ships addresses cable network installation. This article covers the 1 January 2026 version. Paragraph 1.1.1 covers self-propelled ships not engaged in international voyages and the navigational equipment intended for them. Consider flag Administration instructions under paragraph 1.1.3. Determine applicability separately for other vessels.

The echo sounder is a practical example of planning the cable installation. The section does not authorize arbitrary extension of the transducer cable or replace the manufacturer’s requirements for a particular measurement chain. This article provides neither a wiring diagram nor a measurement procedure.

Specify the cable type and route

Paragraph 3.5.1 requires shielded cables for external wiring of navigational equipment. Route them according to the manufacturer’s technical documentation, taking into account Part XI, Electrical Equipment, of the Rules for the Classification and Construction of Sea-Going Ships.

For a quotation, identify the cable type if known, its purpose and the current wiring diagram. If there are no markings, state that the type is unknown. A shielded cable with the right number of cores is not automatically a suitable replacement. Confirm suitability for the particular equipment and connection.

The NED-3010 listing specifies an NXD-200A transducer with a 15 m cable. This describes the offered configuration and does not establish the allowable length of every modified route. If the vessel has a different route, agree on a solution using the applicable documentation. Do not assume an arbitrary splice can supply the extra length or that all existing connections suit the new unit.

Document bends in the installation data

Paragraph 3.5.4 requires the minimum permissible inside bend radius to be observed for cables and microwave transmitting feeders. It does not specify a single numerical value for all cables.

Show the total route and identify tight bends, enclosure entries and diversions around structures. Determine the required radius and permissible construction from the applicable cable documentation. An intact-looking jacket or a cable that physically fits through an opening does not establish suitability.

Identify connections on the exposed deck

Paragraph 3.5.3 requires connections on the exposed deck to have IP56 water protection to prevent moisture from entering the cables. This requirement concerns the location of the connection. The display’s protection rating cannot substitute for it.

In the enquiry, identify continuous sections, connectors and which connections are on the exposed deck. Confirm protection for the finished connection using its documentation. A selected enclosure or seal alone does not establish the protection of an unspecified assembly. If the connection must change, include the materials and work in the agreed schedule.

Record the cable test separately

Paragraph 3.5.2 requires at least 20 MΩ insulation resistance for the installed cable regardless of length, with the cable disconnected at both ends. Retain that condition when reading the requirement. It does not describe measurement through connected electronics.

The contractor determines test settings and permitted actions using the applicable documents. For a quotation, supply any existing test report, the cable identification and known observations. This article does not call for disconnecting equipment or testing insulation on an operational installation.

Information for agreeing the scope

ItemWhat to specify
Equipment at the ends of the lineFull designations of the units and transducer
Cable to be retainedType, purpose, known length and documentation
Cable routeRoute diagram, penetrations, bends and available information on entries
ConnectionsLocations, configurations and any sections on the exposed deck
ConditionExisting test reports and observations, without additional testing by the requester
QuotationNew parts, retained items, accessories and scope of work

For NED-3010 tie this schedule to the exact supply scope. The transducer well, transducer suitability and cable network are related but distinct parts of a refit. A decision about one does not establish suitability of the others. Confirm availability, version, documentation, contents, price and lead time in the current quotation.

Sources

The table and enquiry questions are practical editorial explanations. Sources reviewed: 25 October 2026, Astana.

More in this series

Request a quote